View RT9183L-18PGF_875961.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

rt9183 1 ds9183-12 march 2007 www.richtek.com ultra low dropout 1.5a linear regulator general description the rt9183 series are high performance linear voltage regulators that provide ultra low-dropout voltage, high output current with low ground current. it operates from an input of 2.3v to 5.5v and provides output current up to 1.5a thus is suitable to drive digital circuits requiring low voltage at high currents. the rt9183 has superior regulation over variations in line and load. also it provides fast respond to step changes in load. other features include over-current and over- temperature protection. the adjustable version has enable pin to reduce power consumption in shutdown mode. the devices are available in fixed output voltag es of 1.2v, 1.8v, 2.5v, 3.3v and as an adjustable device with a 0.8v reference voltage. the rt9183 regulators are available in 3-lead sot-223 and to-263 packages (fixed output only for the 3-lead option). also available are 5-lead to-263 and fused sop-8 packages with two external resistors to set the output voltage ranges from 0.8v to 4.5v. ordering information features z z z z z 330mv dropout @ 1.5a z z z z z 380 a low ground pin current z z z z z excellent line and load regulation z z z z z 0.1 a quiescent current in shutdown mode z z z z z guaranteed 1.5a output current z z z z z fixed output voltages : 1.2v, 1.8v, 2.5v, 3.3v z z z z z adjustable output voltage from 0.8v to 4.5v z z z z z over-temperature/over-current protection z z z z z rohs compliant and 100% lead (pb)-free applications z battery-powered equipment z mother board/graphic card z peripheral cards z pcmcia card pin configurations (top view) sop-8 2 3 4 5 8 7 6 gnd en vin vout adj gnd gnd gnd 23 1 gnd vout (tab) vin sot-223 (f-type) sot-223 23 1 vin gnd (tab) vout to-263 23 1 vin gnd(tab) vout to-263-5 4 23 5 1 en gnd(tab) vin vout adj note : richtek pb-free and green products are : ` rohs compliant and compatible with the current require- ments of ipc/jedec j-std-020. ` suitable for use in snpb or pb-free soldering processes. ` 100%matte tin (sn) plating. rt9183 package type g : sot-223 gf : sot-223 (f-type) s : sop-8 m : to-263 m5 : to-263-5 operating temperature range p : pb free with commercial standard g : green (halogen free with commer- cial standard) output voltage defauit : adjustable 12 : 1.2v 18 : 1.8v 25 : 2.5v 33 : 3.3v - h : chip enable high l : chip enable low
rt9183 2 ds9183-12 march 2007 www.richtek.com typical application circuit figure 1. 3.3v to 2.5v regulator figure 2. adjustable operation )volts r2 r1 (1 0.8 v out + = note: the value of r2 should be less than 80k to maintain regulation. figure 3. fixed operation with sop-8 and to-263-5 packages 2.5v, 1.5a (sot-223 & to-263) rt9183 vin vout gnd v out v in = 3.3v c in c out 10uf 10uf vin vout en gnd adj (sop-8 & to-263-5) rt9183 v out v in enable c in c out c 10uf 0.1uf 10uf (sop-8 & to-263-5) vin vout en gnd adj rt9183 v out v in enable c in c out c 10uf 0.1uf 10uf r 1 r 2
rt9183 3 ds9183-12 march 2007 www.richtek.com function block diagram functional pin description pin name pin function en chip enable control input. note that the device will be in the unstable state if the pin is not connected. vin supply input gnd common ground vout regulator output adj the output voltage is set by the internal feedback resistors when this pin grounded. if external feedback resistors are applied, the output voltage will be: v out = 0.8 (1 + ) volts 2 1 r r thermal shutdown vout shutdown logic en gnd output mode comparator + - adj vin error amplifier + - 0.8v reference current limit sensor + - 100mv
rt9183 4 ds9183-12 march 2007 www.richtek.com electrical characteristics (v in = v out + 0.7v, c in =c out = 10 f (ceramic), t a = 25 c unless otherwise specified) recommended operating conditions (note 3) z supply input v oltage ------------------------------------------------------------------------------------------------------ 2.3v to 5.5v z junction temperature range -------------------------------------------------------------------------------------------- ? 40 c to 125 c absolute maximum ratings (note 1) z supply input v oltage ------------------------------------------------------------------------------------------------------ 6v z package thermal resistance sot-223, ja ---------------------------------------------------------------------------------------------------------------- 115 c/w sot-223, jc --------------------------------------------------------------------------------------------------------------- 15 c/w sot-223 (f-type), ja ---------------------------------------------------------------------------------------------------- 135 c/w sot-223 (f-type), jc ---------------------------------------------------------------------------------------------------- 17 c/w sop-8, ja ------------------------------------------------------------------------------------------------------------------ 125 c/w sop-8, jc ------------------------------------------------------------------------------------------------------------------ 20 c/w to-263, ja ----------------------------------------------------------------------------------------------------------------- 45 c/w to-263, jc ----------------------------------------------------------------------------------------------------------------- 8 c/w z power dissipation, p d @t a = 25 c sot-223 --------------------------------------------------------------------------------------------------------------------- 0.87w sot-223 (f-type) ---------------------------------------------------------------------------------------------------------- 0.74w sop-8 ------------------------------------------------------------------------------------------------------------------------ 0.8w to-263 ----------------------------------------------------------------------------------------------------------------------- 2.22w z lead temperature (soldering, 10 sec.) ------------------------------------------------------------------------------- 260 c z junction temperature ----------------------------------------------------------------------------------------------------- 150 c z storage temperature range -------------------------------------------------------------------------------------------- ? 65 c to 150 c z esd susceptibility (note 2) hbm (human body mode) ---------------------------------------------------------------------------------------------- 2kv mm (machine mode) ------------------------------------------------------------------------------------------------------ 200v parameter symbol test conditions min typ max units output voltage accuracy (fixed output voltage) v out i out = 1 0ma ? 2 0 +2 % output voltage r ange (adjustable) v out_adj 0.8 -- 4.5 v quiescent current (note 6) i q i out = 0ma, enable -- 380 500 a standby current (note 7) i stby v in = 5.5v, shutdown -- 0.1 1 a current limit i lim 2 3.2 4.2 a dropout voltage (note 4) v drop i out = 0.5a -- 110 300 mv i out = 1.0a -- 220 400 i out = 1.5a -- 330 500 line r egulation v line v out + 0.7v < v in < 5.5v i out = 1 0m a -- 0.035 0.18 %/v to be continued
rt9183 5 ds9183-12 march 2007 www.richtek.com parameter symbol test conditions min typ max units load regulation (note 5) (fixed output voltage) v load 1ma < i out < 1.5a -- 22 45 mv thermal shutdown temperature t sd -- 170 -- c thermal shutdown hysteresis t sd -- 30 -- c logic-low voltage v il v in = 5.5v -- -- 0.6 en threshold logic-high voltage v ih v in = 5.5v 1.8 -- -- v enable pin current i en v in = 5.5v, enable -- 0.1 1 a adj reference voltage tolerance v ref 0.784 0.8 0.816 v adjust pin current i adj v adj = v ref -- 10 100 na adjust pin threshold v th(adj) 0.05 0.1 0.2 v note 1. stresses listed as the above "absolute maximum ratings" may cause permanent damage to the device. these are for stress ratings. functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. exposure to absolute maximum rating conditions for extended periods may remain possibility to affect device reliability. note 2. devices are esd sensitive. handling precaution recommended. note 3. the device is not guaranteed to function outside its operating conditions. note 4. the dropout voltage is defined as v in -v out , which is measured when v out is v out(normal) ? 100mv. note 5. regulation is measured at constant junction temperature by using a 20ms current pulse. devices are tested for load regulation in the load range from 10ma to 1.5a. note 6. quiescent, or ground current, is the difference between input and output currents. it is defined by i q = i in - i out under no load condition (i out = 0ma). the total current drawn from the supply is the sum of the load current plus the ground pin current. note 7. standby current is the input current drawn by a regulator when the output voltage is disabled by a shutdown signal (v en >1.8v ). it is measured with v in = 5.5v. note 8. ja is measured in natural convection (still air) at t a = 25 c with the component mounted on a low effective thermal conductivity test board of jedec 51-3 thermal measurement standard. and the cooper area of pcb layout is 4mm x 2.5mm on sot-223, 14mm x 14mm on to-263 for thermal measurement.
rt9183 6 ds9183-12 march 2007 www.richtek.com typical operating characteristics output voltage vs. temperature 1.7 1.75 1.8 1.85 1.9 -50 -25 0 25 50 75 100 125 temperature output voltage (v) ( c ) rt9183h-18cs v in = 5v, r l = c in = c out = 10uf (ceramic,y5v) output voltage vs. temperature 2.4 2.45 2.5 2.55 2.6 -50 -25 0 25 50 75 100 125 temperature output voltage (v) v in = 5v, r l = c in = c out = 10uf (ceramic,y5v) ( c ) rt9183-25cg quiescent current vs. temperature 300 320 340 360 380 400 -50 -25 0 25 50 75 100 125 temperature quiescent current (ua) 1 v in = 5v, r l = c in = c out = 10uf (ceramic,y5v) rt9183h-18cs ( c ) quiescent current vs. temperature 300 320 340 360 380 400 -50 -25 0 25 50 75 100 125 temperature quiescent current (ua) 1 ( c ) v in = 5v, r l = c in = c out = 10uf (ceramic,y5v) rt9183-25cg current limit vs. temperature 3 3.2 3.4 3.6 3.8 4 -50 -25 0 25 50 75 100 125 temperature current limit (a) ( c ) v in = 5v, c in = c out = 10uf(ceramic,y5v) rt9183-25cg current limit vs. temperature 3 3.2 3.4 3.6 3.8 4 -50 -25 0 25 50 75 100 125 temperature current limit (a) ( c ) v in = 5v, c in = c out = 10uf(ceramic,y5v) rt9183l-33cm5
rt9183 7 ds9183-12 march 2007 www.richtek.com load transient response time (100us/div) -50 50 0 0 1 load current (a) output voltage deviation(mv) rt9183h-18cs c out = 47uf/low esr, i load = 1ma to 1.5a 2 load transient response rt9183h-18cs time (100us/div) c out = 47uf/low esr, i load = 1ma to 750ma load current (a) output voltage deviation(mv) -20 20 0 0 0.5 1 dropout voltage 0 100 200 300 400 500 0 0.3 0.6 0.9 1.2 1.5 load current (a) dropout voltage (mv) t j = +25 c t j = 125 c t j = -40 c rt9183l-33cm5 dropout voltage vs. load current dropout voltage 0 100 200 300 400 500 0 0.3 0.6 0.9 1.2 1.5 load current (a) dropout voltage (mv) 1 t j = +25 c t j = 125 c t j = -40 c rt9183-25cg dropout voltage vs. load current load transient regulation time (100us/div) c out = 47uf/low esr output voltage deviation(mv) load current (ma) i load = 1ma to 750ma 500 0 20 0 rt9183-12cgf dropout voltage vs. load current 0 100 200 300 400 0 0.3 0.6 0.9 1.2 1.5 load current (a) dropout voltage (mv) t j = 125 c t j = 25 c t j = -40 c rt9183h-cs v out = 3.3v
rt9183 8 ds9183-12 march 2007 www.richtek.com en pin shutdown threshold vs. temperature 0.7 0.8 0.9 1 1.1 -50 -25 0 25 50 75 100 125 temperature shutdown threshold voltage (v) 1 rt9183l-33cm5 v out off to on v out on to off ( c ) en pin shutdown response rt9183h-18cs time (500us/div) c in = c out = 10uf (ceramic,y5v) i load = 100ma, v in = 5v, t a =25 c en voltage (v) output voltage (v) 0 2 1 0 5 reference voltage vs. temperature 0.75 0.77 0.79 0.81 0.83 0.85 -50 -25 0 25 50 75 100 125 temperature reference voltage (v) ( c ) v in = 5v,c in = c out = 10uf (electrolysis) rt9183h-cs line transient regulation time (100us/div) input voltage deviation(v) output voltage deviation(mv) c out = 47uf/low esr i load = 100ma 5 4 10 0 rt9183-12cgf time (100us/div) rt9183h-18cs c out = 47uf/low esr, i load = 100ma input voltage deviation(v) output voltage deviation(mv) line transient response -10 10 0 4 5
rt9183 9 ds9183-12 march 2007 www.richtek.com input capacitor an input capacitance of ? 10 f is required between the device input pin and ground directly (the amount of the capacitance may be increased without limit). the input capacitor must be located less than 1 cm from the device to assure input stability (see pcb layout section). a lower esr capacitor allows the use of less capacitance, while higher esr type (like aluminum electrolytic) require more capacitance. capacitor types (aluminum, ceramic and tantalum) can be mixed in parallel, but the total equivalent input capacitance/ esr must be defined as above to stable operation. there are no requirements for the esr on the input capacitor, but tolerance and temperature coefficient must be considered when selecting the capacitor to ensure the capacitance will be ? 10 f over the entire operating temperature range. output capacitor the rt9183 is designed specifically to work with very small ceramic output capacitors. the recommended minimum capacitance (temperature characteristics x7r or x5r) are 10 f to 47 f range with 10m to 25m range ceramic capacitors between each ldo output and gnd for transient stability, but it may be increased without limit. higher capacitance values help to improve transient. the output capacitor's esr is critical because it forms a zero to provide phase lead which is required for loop stability. application information like any low-dropout regulator, the rt9183 series requires input and output decoupling capacitors. these capacitors must be correctly selected for good performance (see capacitor characteristics section). please note that linear regulators with a low dropout voltage have high internal loop gains which require care in guarding against oscillation caused by insufficient decoupling capacitance. no load stability the device will remain stable and in regulation with no external load. this is specially important in cmos ram keep-alive applications. input-output (dropout) voltage a regulator's minimum input-to-output voltage differential (dropout voltage) determines the lowest usable supply voltage. in battery-powered systems, this determines the useful end-of-life battery voltage. because the device uses a pmos, its dropout voltage is a function of drain-to-source on-resistance, r ds(on) , multiplied by the load current: v dropout = v in - v out = r ds(on) i out current limit the rt9183 monitors and controls the pmos' gate voltage, minimum limiting the output current to 2a . the output can be shorted to ground for an indefinite period of time without damaging the part. short-circuit protection the device is short circuit protected and in the event of a peak over-current condition, the short-circuit control loop will rapidly drive the output pmos pass element off. once the power pass element shuts down, the control loop will rapidly cycle the output on and off until the average power dissipation causes the thermal shutdown circuit to respond to servo the on/off cycling to a lower frequency. please refer to the section on thermal information for power dissipation calculations. capaacitor characteristics it is important to note that capacitance tolerance and variation with temperature must be taken into consideration when selecting a capacitor so that the minimum required amount of capacitance is provided over the full operating temperature range. in general, a good tantalum capacitor will show very little capacitance variation with temperature, but a ceramic may not be as good (depending on dielectric type). aluminum electrolytics also typically have large temperature variation of capacitance value.
rt9183 10 ds9183-12 march 2007 www.richtek.com equally important to consider is a capacitor 's esr change with temperature: this is not an issue with ceramics, as their esr is extremely low. however, it is very important in tantalum and aluminum electrolytic capacitors. both show increasing esr at colder temperatures, but the increase in aluminum electrolytic capacitors is so severe they may not be feasible for some applications. ceramic: for values of capacitance in the 10 f to 100 f range, ceramics are usually larger and more costly than tantalums but give superior ac performance for by-passing high frequency noise because of very low esr (typically less than 10m ). however, some dielectric types do not have good capacitance characteristics as a function of voltage and temperature. z5u and y5v dielectric ceramics have capacitance that drops severely with applied voltage. a typical z5u or y5v capacitor can lose 60% of its rated capacitance with half of the rated voltage applied to it. the z5u and y5v also exhibit a severe temperature effect, losing more than 50% of nominal capacitance at high and low limits of the temperature range. x7r and x5r dielectric ceramic capacitors are strongly recommended if ceramics are used, as they typically maintain a capacitance range within 20% of nominal over full operating ratings of temperature and voltage. of course, they are typically larger and more costly than z5u/ y5u types for a given voltage and capacitance. tantalum: solid tantalum capacitors are recommended for use on the output because their typical esr is very close to the ideal value required for loop compensation. they also work well as input capacitors if selected to meet the esr requirements previously listed. tantalums also have good temperature stability: a good quality tantalum will typically show a capacitance value that varies less than 10~15% across the full temperature range of 125 c to -40 c. esr will vary only about 2x going from the high to low temperature limits. the increasing esr at lower temperatures can cause oscillations when marginal quality capacitors are used (if the esr of the capacitor is near the upper limit of the stability range at room temperature). aluminum: this capacitor type offers the most capacitance for the money. the disadvantages are that they are larger in physical size, not widely available in surface mount, and have poor ac performance (especially at higher frequencies) due to higher esr and esl. compared by size, the esr of an aluminum electrolytic is higher than either tantalum or ceramic, and it also varies greatly with temperature. a typical aluminum electrolytic can exhibit an esr increase of as much as 50x when going from 25 c down to -40 c. it should also be noted that many aluminum electrolytics only specify impedance at a frequency of 120hz, which indicates they have poor high frequency performance. only aluminum electrolytics that have an impedance specified at a higher frequency (between 20khz and 100khz) should be used for the device. derating must be applied to the manufacturer's esr specification, since it is typically only valid at room temperature. any applications using aluminum electrolytics should be thoroughly tested at the lowest ambient operating temperature where esr is maximum. thermal considerations thermal protection limits power dissipation in rt9183. when the operation junction temperature exceeds 170 c, the otp circuit starts the thermal shutdown function and turns the pass element off. the pass element turns on again after the junction temperature cools by 30 c. for continuous operation, do not exceed absolute maximum operation junction temperature 125 c. the power dissipation definition in device is: p d = (v in ? v out ) x i out + v in x i q
rt9183 11 ds9183-12 march 2007 www.richtek.com the maximum power dissipation depends on the thermal resistance of ic package, pcb layout, the rate of surroundings airflow and temperature difference between junction to ambient. the maximum power dissipation can be calculated by following formula: p d(max) = ( t j(max) - t a ) / ja where t j(max) is the maximum operation junction temperature 125 c, t a is the ambient temperature and the ja is the junction to ambient thermal resistance. for recommended operating conditions specification of rt9183, where t j(max) is the maximum junction temperature of the die (125 c) and t a is the maximum ambient temperature. the junction to ambient thermal resistance ( ja is layout dependent) for sot-223 package is 115 c/w, sot-223 package (f-type) is 135 c/w, sop-8 package is 125 c/w, and to-263 package is 45 c/w on standard jedec 51-3 thermal test board. the maximum power dissipation depends on operating ambient temperature for fixed t j(max) and thermal resistance ja . for rt9183 packages, the figure 4 of derating curves allows the designer to see the effect of rising ambient temperature on the maximum power allowed. pcb layout good board layout practices must be used or instability can be induced because of ground loops and voltage drops. the input and output capacitors must be directly connected to the input, output, and ground pins of the device using traces which have no other currents flowing through them. the best way to do this is to layout c in and c out near the device with short traces to the v in , v out , and ground pins. the regulator ground pin should be connected to the external circuit ground so that the regulator and its capacitors have a? single point ground? . it should be noted that stability problems have been seen in applications where ? vias ? to an internal ground plane were used at the ground points of the device and the input and output capacitors. this was caused by varying ground potentials at these nodes resulting from current flowing through the ground plane. using a single point ground technique for the regulator and it's capacitors fixed the problem. since high current flows through the traces going into v in and coming from v out , kelvin connect the capacitor leads to these pins so there is no voltage drop in series with the input and output capacitors. optimum performance can only be achieved when the device is mounted on a pc board according to the diagram below: sop-8 board layout gnd adj gnd gnd v in v out en + + + figure 4 0 400 800 1200 1600 2000 2400 0 25 50 75 100 125 ambient temperature ( ) maximum power dissipation (mw) ( c) sot-223 to-263 sop-8 sot-223 ( f-type )
rt9183 12 ds9183-12 march 2007 www.richtek.com adjustable operation the adjustable version of the rt9183 has an output voltage range of 0.8v to 4.5v. the output voltage is set by the ratio of two external resistors as shown in figure 2. the value of r2 should be less than 80k to maintain regulation. in critical applications, small voltage drop is caused by the resistance (r t ) of pc traces between the ground pin of the device and the return pin of r2 (see figure 5 shown on next page). note that the voltage drop across the external pc trace will add to the output voltage of the device. optimum regulation will be obtained at the point where the return pin of r2 is connected to the ground pin of the device directly. referring to figure 3 the fixed voltage versions for both sop-8 and to-263-5 packages, the adj pin is the input to the error amplifier and must be tied the ground pin of the device directly otherwise it will be in the unstable state if the pin voltage more than 0.1v with respect to the ground pin itself. figure 5. return pin of external resistor connection (sop-8 & to-263-5) vin vout en gnd adj rt9183 v out v in enable c in c out c 10uf 0.1uf 10uf r 1 r 2 r t
rt9183 13 ds9183-12 march 2007 www.richtek.com outline dimension dimensions in millimeters dimensions in inches symbol min max min max a 1.450 1.803 0.057 0.071 a1 0.020 0.100 0.0008 0.0047 b 0.610 0.787 0.024 0.031 b 3.302 3.708 0.130 0.146 c 6.706 7.290 0.264 0.287 d 6.299 6.706 0.248 0.264 d1 2.896 3.150 0.114 0.124 e 2.261 2.362 0.089 0.093 h 0.229 0.330 0.009 0.013 l 1.550 1.950 0.061 0.077 l1 0.800 1.100 0.009 0.013 3-lead sot-223 surface mount package a a1 b h b d d1 c l e e l1
rt9183 14 ds9183-12 march 2007 www.richtek.com a b j f h m c d i 8-lead sop plastic package dimensions in millimeters dimensions in inches symbol min max min max a 4.801 5.004 0.189 0.197 b 3.810 3.988 0.150 0.157 c 1.346 1.753 0.053 0.069 d 0.330 0.508 0.013 0.020 f 1.194 1.346 0.047 0.053 h 0.170 0.254 0.007 0.010 i 0.050 0.254 0.002 0.010 j 5.791 6.200 0.228 0.244 m 0.400 1.270 0.016 0.050
rt9183 15 ds9183-12 march 2007 www.richtek.com c b2 a l1 b e e l2 v u d b b1 dimensions in millimeter s dimensions in inches symbol min max min max a 4.064 4.826 0.160 0.190 b 1.143 1.676 0.045 0.066 b 0.660 0.914 0.026 0.036 b1 1.143 1.397 0.045 0.055 b2 0.305 0.584 0.012 0.023 c 1.143 1.397 0.045 0.055 d 9.652 10.668 0.380 0.420 e 8.128 9.652 0.320 0.380 e 2.286 2.794 0.090 0.110 l1 14.605 15.875 0.575 0.625 l2 2.286 2.794 0.090 0.110 u 6.223 ref. 0.245 ref. v 7.620 ref. 0.300 ref. 3-lead to- 263 surface mount
rt9183 16 ds9183-12 march 2007 www.richtek.com richtek technology corporation headquarter 5f, no. 20, taiyuen street, chupei city hsinchu, taiwan, r.o.c. tel: (8863)5526789 fax: (8863)5526611 richtek technology corporation taipei office (marketing) 8f, no. 137, lane 235, paochiao road, hsintien city taipei county, taiwan, r.o.c. tel: (8862)89191466 fax: (8862)89191465 email: marketing@richtek.com dimensions in millimeter s dimensions in inches symbol min max min max a 4.064 4.826 0.160 0.190 b 1.143 1.676 0.045 0.066 b 0.660 0.914 0.026 0.036 b2 0.305 0.584 0.012 0.023 c 1.143 1.397 0.045 0.055 d 9.652 10.668 0.380 0.420 e 8.128 9.652 0.320 0.380 e 1.524 1.829 0.060 0.072 l1 14.605 15.875 0.575 0.625 l2 2.286 2.794 0.090 0.110 u 6.223 ref. 0.245 ref. v 7.620 ref. 0.300 ref. 5-lead to-263 plastic surface mount package c b2 a b e v u d e l1 b l2

▲Up To Search▲

Price & Availability of RT9183L-18PGF

	To Download RT9183L-18PGF Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .